- Home
- Skills
- APIs & Backend
- tsv process engineer
Works with the AI Agents you already use
tsv process engineer
Expert TSV process engineering for 3D IC fabrication, Bosch process etching, and Cu metallization troubleshooting.
$5
/moSubscription · cancel anytime
Secure checkout via Stripe
- Always the latest version
- Delivered live to your agent via MCP
- Cancel anytime, access ends at period end
tsv process engineer
Example session with this skill installed
We are seeing significant voiding at the bottom of 10:1 aspect ratio TSVs after Cu electroplating. The via is 5um wide. What is the root cause and how do we fix the recipe?
- Read your context and instructions
- Compiled the tsv process engineer
The observed voiding in 10:1 AR TSVs typically indicates a failure in either the PVD seed coverage or the ECD additive balance, preventing a true bottom-up fill.
TSV Cu Fill Analysis
| Symptom | Probable Root Cause | Recommended Parameter Adjustment |
|---|---|---|
| Bottom Voids | Discontinuous PVD Cu seed at via base | Increase PVD bias power; target >50nm thickness at bottom |
| Bottom Voids | Suppressor/Accelerator imbalance | Increase Accelerator concentration; reduce plating current density (J) |
| Center Seams | Premature top pinch-off | Increase Suppressor concentration; check for Leveler depletion |
| Cu Protrusion | Thermal expansion mismatch | Add 250°C anneal step post-plating to stabilize Cu grain |
Recommended Action Plan
Seed Layer Audit: Verify bottom-side seed coverage via FIB-SEM. If coverage is <20nm, increase PVD deposition time or optimize collimated sputtering parameters.
2. ECD Recipe Tuning:
- Initial Entry: Low current density (0.5 ASD) for 5 minutes to protect the seed.
- Bulk Fill: Ramp to 1.5 - 2.0 ASD using a 3-additive system (VMS, Suppressor, Accelerator, Leveler).
- Chemistry: Ensure Accelerator/Suppressor ratio is optimized for 10:1 AR to promote "superfilling."
Metrology: Perform cross-sectional SEM on a coupon at the wafer center and edge to check for CD uniformity and fill consistency.
Next steps
- Verify PVD barrier/seed thickness at the via bottom using FIB-SEM.
- Run a 3-factor DOE on Accelerator concentration (e.g., 5, 10, 15 mL/L).
- Calibrate the plating tool's flow rate to ensure uniform additive delivery to the via mouth.
Subscription · always the latest version
- Secure checkout via Stripe
- Cancel anytime
- Delivered live via MCP
About this skill
Scaling 3D IC and HBM production requires precise control over high-aspect-ratio features where minor deviations lead to total yield loss. This skill provides the deep domain expertise needed to stabilize TSV fabrication, from Bosch process tuning to backside via reveal.
What it does
- Process integration provides complete fabrication flows for silicon interposers and high-bandwidth memory (HBM).
- Etch optimization delivers specific Bosch process parameters for SF6/C4F8 flow, power, and cycle timing to control scalloping.
- Defect troubleshooting identifies root causes for Cu voids, seams, and protrusion using a structured matrix.
- Metallization design configures bottom-up Cu electroplating recipes including additive ratios for suppressors and accelerators.
- Metrology planning defines characterization strategies using SEM, FIB, and X-ray to verify via continuity.
How it works
- Define the geometry by providing via diameter, depth, and target aspect ratio (AR).
- Select the process step such as DRIE, PECVD insulation, PVD barrier/seed, or Cu ECD fill.
- Analyze the defect by describing symptoms like leakage or high resistance for a root cause report.
- Generate the recipe to receive specific parameter ranges and SPC control plan recommendations.
Frameworks & tools
This skill is built for semiconductor process engineers working with DRIE systems, electroplating tools, and CMP platforms. It references SEMI standards, JEDEC reliability tests, and IEEE EPS roadmaps.
Why this beats prompting it yourself
Generic AI lacks the specific knowledge of Bosch cycle chemistry and Cu protrusion mechanics required for sub-micron TSV engineering. This skill applies a specialized troubleshooting matrix and strict KPI targets that standard models frequently hallucinate or generalize.
Use cases
- Stabilize high-aspect-ratio via etching to reduce sidewall roughness and footing.
- Resolve voiding issues in 10:1 AR Cu electroplating flows.
- Optimize CMP slurry selectivity to prevent dishing and Cu residue.
- Design a backside reveal process that minimizes stress-induced Cu pumping.
Known limitations
Does not provide tool-specific G-code or proprietary vendor recipes for specific hardware models. Output is limited to industry-standard parameter ranges and best practices.
Requires specific via dimensions (AR, diameter) for accurate recipes. Does not provide proprietary vendor-specific tool software commands.
How to use
- 1
Connect your agent to the Agensi MCP
Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup
- 2
Sign in to Agensi
Your agent shows a sign-in link. Sign in and click Allow.
- 3
Ask for what you need
Your agent loads this skill and uses it on your task. It always asks before any payment.
Reviews
No reviews yet
Be one of the first to try it. Every listed skill goes through the trust checks below.
Security scanned
Checked by our 8-point scan before listing
Fresh listing
Recently published to Agensi
Free forever
No account required to browse
Trust & safety
Security scan
Security scan passed 22 days ago
Permissions
No special permissions declared or detected