Works with the AI Agents you already use

    Claude CodeClaude CodeCursorCursorCodex CLICodex CLIMuseMuseDotsDots+21 more

    Router & Mesh Wi-Fi Health Check

    1

    Read-only check of your router or mesh from the LAN: firmware, ports, UPnP, Wi-Fi, DNS path, double NAT.

    $2

    Secure checkout via Stripe

    Money-back guarantee

    Converts to your local currency at checkout

    Security scanned
    Router & Mesh Wi-Fi Health Check

    Router & Mesh Wi-Fi Health Check

    Example session with this skill installed

    Health check my router. It's a TP-Link Deco mesh and I'm on Windows.

    • Read your context and instructions
    • Compiled the router & mesh

    I ran the read-only probe from your PC against the gateway. Nothing was changed. Deco is an app-first mesh, so the web page shows little: the router settings below need a few screenshots from you (list at the end).

    Facts

    Gateway192.168.1.1 (TP-Link Deco, main node)
    DNS handed out192.168.1.20 (Pi-hole) and 8.8.8.8
    Latency to gateway2 ms, 0 % loss over 20 pings
    Latency to 1.1.1.111 ms, 0 % loss
    WAN addressprivate: second router in front (double NAT)
    UPnPanswers; 2 port mappings listed
    Open ports on gateway53, 80, 443

    Assessment

    DNS filter: needs attention. The router also hands out 8.8.8.8 as a secondary DNS, so any device can skip the Pi-hole. doubleclick.net resolves through 8.8.8.8 but not through the Pi-hole.

    • IPv6 DNS: needs attention. Devices also get an IPv6 DNS server that bypasses the Pi-hole.
    • UPnP: check. 2 mappings exist that I cannot match to a device: TCP 51413 and UDP 51413.

    Double NAT: low. The WAN address is private, so another router sits in front. Port forwarding will not work from outside until that one is in bridge mode.

    • Latency and loss: good.

    Prioritized actions

    Good as it is: latency, packet loss, no remote admin port open on the gateway.

    Should change
    1.

    Remove the secondary DNS 8.8.8.8. In the Deco app: More > Advanced > DHCP Server, set only the Pi-hole as DNS. Why: otherwise ads and trackers skip your filter.
    2. Turn off the IPv6 DNS that bypasses the Pi-hole, or hand the Pi-hole's IPv6 address out instead.
    3.

    Find out what uses port 51413. It is usually a torrent client. If nobody recognizes it, switch UPnP off and see what stops working.

    Check: whether the ISP box in front can run in bridge mode to get rid of double NAT.

    What I need from you

    1. Screenshot: Deco app > More > Wi-Fi settings (security mode per network, WPS).
    2. Screenshot: More > Advanced > Firmware (version and auto-update).
    3. Screenshot: More > Advanced > Guest network (on or off).

    Sources

    Findings are saved to ~/.home-health-check/findings/. Send the screenshots and I'll update this report.

    Connects securely to your tools. The creator never sees your data.

    About this skill

    Checks your home router or mesh Wi-Fi (TP-Link Deco, Eero, Google/Nest Wifi, Asus, Netgear, Ubiquiti, Fritz!Box, ISP routers and others) from a computer on your network. A read-only probe actively pings and port-checks the gateway, but changes nothing. It looks at the gateway's open ports, UPnP and existing port mappings, the DNS servers it hands out and whether a DNS filter can be bypassed (also over IPv6), double NAT and CGNAT, latency and packet loss, and nearby Wi-Fi networks. Firmware, Wi-Fi security, WPS, remote admin and guest network come from the router's web page (you sign in yourself) or from screenshots of its app. Ends with a prioritized fix list.

    Works on its own. With the other Home Health Check skills it shares one private data folder, and the Home Network Report combines everything into one fix list. Open source (MIT).

    Sees what a device on the LAN can see; settings behind the router's login or app come from your sign-in or screenshots. App-only mesh systems (Deco, Eero, Google/Nest Wifi) show little on the web, so expect a short screenshot list. Does not test from outside your network. On macOS 15 and later, macOS asks once for Local Network access when the agent runs inside an app (not in Terminal).

    How to use

    1. 1

      Connect your agent to the Agensi MCP

      Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup

    2. 2

      Sign in to Agensi

      Your agent shows a sign-in link. Sign in and click Allow.

    3. 3

      Ask for what you need

      Your agent loads this skill and uses it on your task. It always asks before any payment.

    Reviews

    No reviews yet

    Be one of the first to try it. Every listed skill goes through the trust checks below.

    Security scanned

    Checked by our 8-point scan before listing

    Fresh listing

    Recently published to Agensi

    Money-back guarantee

    Doesn't do what its page promises? You get your money back.

    Trust & safety

    Security scan

    Security scan passed 3 days ago

    Permissions

    Terminal / Shell
    Network Access
    Write Files
    Read Files
    Browser
    Environment Variables

    File Scopes

    ~/.home-health-check/**
    $HOME_HEALTH_CHECK_DIR/**

    aTerminal: runs the bundled read-only probe (PowerShell on Windows, bash on macOS/Linux), no admin rights or sudo. Network: mostly your LAN (the gateway, its DNS servers, an SSDP multicast, the router's UPnP description and a read-only port-mapping query; it creates no mappings), plus 20 pings each to 1.1.1.1, 9.9.9.9 and 8.8.8.8, a 3-hop traceroute to 1.1.1.1, and one test lookup of doubleclick.net to see whether DNS filtering applies. Browser (optional): opens the router's page, you sign in yourself, and the agent only reads pages as text; it never types or stores the password. Files: writes the findings and updates the inventory in ~/.home-health-check (or HOME_HEALTH_CHECK_DIR, the only environment variable it reads).

    Listed18 days ago
    Updated3 days ago

    What's inside

    Frequently Asked Questions

    No. In browser mode you sign in yourself and the agent only reads the pages as text; it never types or stores the password. Without a browser it asks you for screenshots instead.

    No. The probe and the page reading are read-only, and it creates no UPnP port mappings. Fixes are steps you do yourself in the router's app or page.

    The probe uses standard protocols and works with any router or mesh on your LAN. The skill has brand-specific tips for common systems (TP-Link Deco, Eero, Google/Nest Wifi, Asus, Netgear, Fritz!Box, Ubiquiti and ISP routers). App-only mesh systems need a few screenshots from you.

    Any agent that can run shell commands on a computer on your home network and supports SKILL.md. Browser mode needs an agent that can control a browser; without one the skill asks for screenshots.

    New in Security