Real-Time Robotics — Measured Latency & Jitter

    1

    PREEMPT_RT, RTOS and ROS 2 control loops with deadline budgets and worst-case latency you can prove by measurement.

    $39

    Secure checkout via Stripe

    Money-back guarantee

    Converts to your local currency at checkout

    Security scanned

    Works with the AI Agents you already use

    Claude CodeClaude CodeCursorCursorCodex CLICodex CLIMuseMuseDotsDots+21 more

    Real-Time Robotics — Measured Latency & Jitter

    Example session with this skill installed

    I have a ROS 2 control loop running at 500Hz on a Raspberry Pi 4. I am seeing intermittent jitter over 500us. Help me audit the latency budget and suggest kernel optimizations.

    • Read your context and instructions
    • Compiled the real-time robotics

    I have analyzed your 500Hz (2ms period) control loop requirements. A 500us jitter represents 25% of your total period, which is high for a Raspberry Pi 4 running standard Linux.

    Latency Audit and Tuning Plan

    StageBudget (us)Strategy
    Sensor Read150SPI/I2C via dedicated bit-banging or high-priority IRQ
    State Estimation400Fixed-point math or optimized Eigen ops
    Controller Logic300ROS 2 StaticSingleThreadedExecutor to avoid overhead
    Actuator Write150DMA-based PWM or dedicated hardware peripheral
    Total Margin1000Remaining time for system interrupts and context switches

    Kernel Optimization Commands

    
    # 1. Isolate CPUs 2 and 3 for the control loop in /boot/cmdline.txt
    # Add: isolcpus=2,3 nohz_full=2,3 rcu_nocbs=2,3
    
    # 2. Set CPU governor to performance to prevent frequency scaling latency
    echo performance | sudo tee /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
    
    # 3. Apply RT priorities to the ROS 2 process (SCHED_FIFO)
    chrt -f -p 98 <ros2_node_pid>
    
    # 4. Move networking and disk IRQs away from isolated cores
    echo 1 | sudo tee /proc/irq/eth0/smp_affinity  # Example for eth0 on Core 0
    

    Measured Latency Analysis

    Run the following to capture the baseline jitter before applying changes:
    cyclictest -l100000 -m -n -p99 -i2000 -h400 > jitter_baseline.txt

    Then process with
    python3 scripts/latency_report.py jitter_baseline.txt --period-us 2000 --deadline-us 500 --cyclictest

    Next steps

    1. Apply mlockall() in your C++ node to prevent page faults during execution.
    2. Set your ROS 2 QoS to Reliable with a small history depth to reduce middleware jitter.
    3. Disable C-states in the firmware to prevent wake-up latency from deep sleep.

    Connects securely to your tools. The creator never sees your data.

    About this skill

    PREEMPT_RT, RTOS and ROS 2 loops with deadlines you can prove.

    Engineer real-time behaviour for robots and drones - PREEMPT_RT Linux, Xenomai, FreeRTOS/Zephyr, CPU isolation and IRQ affinity, scheduling policies, ros2_control loops, DDS/QoS tuning, deadline budgets and measured worst-case latency with jitter analysis. Use when a control loop misses deadlines, the user needs deterministic timing, chooses an RTOS, or must prove latency figures with measurements.

    Includes an EXPERT.md reference (exact parameters, thresholds, failure diagnosis). Tested scripts: scripts/latency_report.py.

    Acceptable use: civil and commercial applications only. Any military, paramilitary or weapon-related use is prohibited, as stated in the skill itself.

    Prohibits military, paramilitary, or weapon-related use. User is responsible for regulatory compliance and safety. Requires manual kernel patching for PREEMPT_RT.

    How to use

    1. 1

      Connect your agent to the Agensi MCP

      Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup

    2. 2

      Sign in to Agensi

      Your agent shows a sign-in link. Sign in and click Allow.

    3. 3

      Ask for what you need

      Your agent loads this skill and uses it on your task. It always asks before any payment.

    Reviews

    No reviews yet

    Be one of the first to try it. Every listed skill goes through the trust checks below.

    Security scanned

    Checked by our 8-point scan before listing

    Fresh listing

    Recently published to Agensi

    Money-back guarantee

    Doesn't do what its page promises? You get your money back.

    Trust & safety

    Security scan

    Security scan passed 28 days ago

    Permissions

    Terminal / Shell
    Read Files
    Listed28 days ago

    What's inside

    Frequently Asked Questions

    This skill identifies and resolves sources of non-determinism, such as page faults, IRQ interference, and task scheduling jitter, ensuring your control loops meet strict sub-millisecond deadlines.

    It is compatible with any AI agent capable of technical system design, including those used for kernel configuration, ROS 2 development, and embedded systems architecture.

    The skill supports a wide range of real-time environments, including PREEMPT_RT Linux, Xenomai, FreeRTOS, and Zephyr, specifically focusing on ROS 2 and DDS middleware optimization.

    You receive the specialized skill logic for latency budgeting, specific kernel/RTOS tuning parameters, and standardized workflows for jitter analysis and DDS QoS configuration.

    While the skill provides the configuration parameters and optimization logic, the user is responsible for manually applying kernel patches (like PREEMPT_RT) and compiling the modified firmware or OS.

    No, this skill is strictly restricted to civil, commercial, and research applications and may not be used for the development of military hardware or weapon systems.

    New in Agents & Orchestration