- Home
- Skills
- Agents & Orchestration
- pcb design master
Works with the AI Agents you already use
pcb design master
Principal-level hardware engineering skill for PCB layout audits, signal integrity, and high-speed circuit design.
$15
pcb design master
Example session with this skill installed
I have a 4-layer board with a 12V to 3.3V 5A Buck converter. The output ripple is higher than expected. Review my SMPS layout strategy and check the PDN impedance.
- Read your context and instructions
- Compiled the pcb design master
I have reviewed your 4-layer SMPS layout and Power Distribution Network. The primary issue is the placement of the input capacitors and the high-side MOSFET switching loop.
Power Integrity & SMPS Audit Report
| Category | Finding | Severity |
|---|---|---|
| Hot-Loop Geometry | The input decoupling caps (C1, C2) are on the bottom layer, connected via 4 vias. This adds ~2.4nH of parasitic inductance, causing $V = L \cdot di/dt$ ringing at the SW node. | [CRITICAL - SPIN REQUIRED] |
| PDN Impedance | Target impedance $Z_{target}$ is 33m$\Omega$. Current MLCC selection (10uF 0603 X5R) suffers 65% capacitance loss at 12V DC bias. Effective capacitance is only 3.5uF. | [HIGH - SI FAILURE RISK] |
| Thermal Rise | The 3.3V 5A output trace is 20 mils wide on 1oz copper. IPC-2152 predicts a $\Delta T$ of $42^\circ\text{C}$, exceeding the $20^\circ\text{C}$ design limit. | [MEDIUM - RELIABILITY] |
| Gate Drive | Missing $R_{boot}$ resistor (series with C3). High $dv/dt$ on the SW node is likely causing CGS Miller-effect turn-on, increasing switching losses. | [MEDIUM - PERFORMANCE] |
Next steps
- Move input capacitors (C1, C2) to the top layer immediately adjacent to the Vin and PGND pins of the IC to eliminate vias in the hot-loop.
- Replace 0603 X5R decoupling caps with 1206 X7R rated for 25V to recover effective capacitance.
- Increase the 3.3V output polygon width to at least 85 mils or utilize a dedicated internal power plane on L3.
- Add a 2.2$\Omega$ resistor in series with the bootstrap capacitor to damp the gate drive.
Connects securely to your tools. The creator never sees your data.
About this skill
Designing hardware at high frequencies or high power is a minefield of parasitic inductance and signal integrity failures. This skill acts as a Principal Hardware Architect to audit every trace, via, and component choice against Maxwell's equations and IPC standards.
What it does
- Physics-based auditing analyzes schematics and layouts using transmission-line theory, semiconductor physics, and thermodynamics.
- Power integrity modeling calculates PDN target impedance and eliminates parallel anti-resonance in decoupling networks.
- High-speed SI analysis manages differential pair skew, phase-velocity mismatch, and fiber-weave effects for multi-gigabit signals.
- SMPS optimization reviews switching regulator hot-loops, snubber values, and Kelvin sense routing to minimize EMI.
- Automated KiCad verification runs structural audits on
.kicad_pcbfiles for DRC, DFM, and signal integrity compliance.
How it works
- Analyze schematics for component derating, DC-bias capacitance loss in MLCCs, and thermal safety margins.
- Define stackup electromagnetics by calculating critical lengths based on driver slew rates and material prepreg styles.
- Audit PCB layout using the 8-Gate Engineering Review sequence from return paths to manufacturing yield.
- Run quantitative scripts to compute exact trace widths, via parasitics, and impedance matching for RF or differential pairs.
Frameworks & tools
Specifically designed for hardware engineers using KiCad, Altium, or Allegro workflows, with deep knowledge of IPC-2152, IEC 62368-1 safety, and CISPR EMC standards.
Why this beats prompting it yourself
Generic AI lacks the hardware-specific rigor to catch DC-bias capacitance drop or parasitic via inductance. This skill enforces a strict 8-Gate review protocol that quantifies physical mechanisms like skin depth and Seebeck offsets, preventing expensive board re-spins.
Use cases
- Audit a high-speed DDR4 or USB-C layout for impedance discontinuities and skew.
- Verify 230V AC mains safety distances and creepage/clearance compliance.
- Size power distribution networks for low-voltage, high-current FPGA rails.
- Debug EMI failures by identifying common-mode radiation paths and loop areas.
Known limitations
Does not perform 3D full-wave EM simulation or SPICE netlist simulation. Requires manual input of specific vendor dielectric constants and silicon slew rates for maximum accuracy.
Does not perform 3D EM simulation or SPICE transient analysis. Requires manual entry of vendor dielectric constants and driver slew rates for precise calculations.
How to use
- 1
Connect your agent to the Agensi MCP
Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup
- 2
Sign in to Agensi
Your agent shows a sign-in link. Sign in and click Allow.
- 3
Ask for what you need
Your agent loads this skill and uses it on your task. It always asks before any payment.
Reviews
No reviews yet
Be one of the first to try it. Every listed skill goes through the trust checks below.
Security scanned
Checked by our 8-point scan before listing
Fresh listing
Recently published to Agensi
Money-back guarantee
Doesn't do what its page promises? You get your money back.
Trust & safety
Security scan
Security scan passed 11 days ago
Requires