Works with the AI Agents you already use

    Claude CodeClaude CodeCursorCursorCodex CLICodex CLIMuseMuseDotsDots+21 more

    NVH FRF & Modal Analysis

    1

    Turn FRF exports from NVH tests or CAE (Nastran, Abaqus, Simcenter) into natural frequencies, half-power damping, Q factors, target-line exceedances and test-vs-simulation correlation (FRAC), with plots and a report.

    Free

    Security scanned

    NVH FRF & Modal Analysis

    Example session with this skill installed

    Analyse test.csv (receptance, real/imag) between 10 and 480 Hz. Give me the natural frequencies and damping, check it against target.csv, and correlate it with my Nastran SOL111 result sim.csv.

    • Read your context and instructions
    • Compiled the nvh frf
    • Generated the data export

    Summary

    Found 3 well-separated modes between 10 and 480 Hz. Two bands exceed the target line, and the simulation is 3-7 % off in frequency with a low FRAC (0.21), so the CAE model needs updating before it can be used for target-setting.

    • Band: 10.0–480.0 Hz, resolution 0.250 Hz, 3 peaks (prominence ≥ 3.0 dB)

    Modes

    modefreq_hzpeak_magpeak_dbprominence_dbdamping_ratio_pctq_factorcoupled_flag
    1423.5902511.126.332.01224.8False
    21180.607075-4.3445.781.533.3False
    33110.0445697-27.0220.63.01716.6False

    Target exceedances

    f_start_hzf_end_hzmax_exceedance_db
    106131.1
    109129.515.66

    Correlation

    • FRAC over band: 0.205
    modef_ref_hzf_cmp_hzdev_pct
    142457.14
    2118112-5.08
    33113213.22

    Findings

    Mode 1 (42 Hz, 2.0 % damping) drives the largest exceedance (+31 dB over the target from 10-61 Hz). This is the primary target for a stiffness or damping countermeasure.

    Mode 2 (118 Hz, 1.5 %) is the most lightly damped mode (Q = 33) and exceeds the target by 15.7 dB between 109 and 130 Hz.

    • No coupled modes were flagged, so the half-power damping estimates are reliable at 0.25 Hz resolution.

    Correlation: simulation over-predicts mode 1 (+7.1 %) and mode 3 (+3.2 %) and under-predicts mode 2 (-5.1 %). Mixed signs point to a local stiffness or mass distribution error rather than a global material property.

    Next steps

    1. Review joint/connection stiffness in the CAE model near the components that dominate mode 1 and mode 2.
    2. Run a sensitivity study, then model-update until frequency deviation is below 3 % and FRAC exceeds 0.8.
    3. Evaluate a damping treatment targeting 100-130 Hz for mode 2.

    Files written: results/modes.csv, results/frf_plot.png, results/report.md.

    modes.csv

    CSV · data export

    Generated

    Example file from a real run - the skill writes it into your workspace.

    Connects securely to your tools. The creator never sees your data.

    About this skill

    What it does

    Give your agent a frequency response function (FRF) file and get an engineering-grade modal summary back:

    • Resonance detection: peak picking with a configurable prominence threshold
    • Modal damping: half-power (-3 dB) bandwidth damping ratio and Q factor per mode
    • Target-line checks: frequency bands where the FRF exceeds your limit, with maximum exceedance in dB
    • Test vs. CAE correlation: matched-mode frequency deviation (%) and FRAC over the band
    • Outputs: modes.csv, magnitude/phase plot (PNG) and a Markdown report

    Who it is for

    NVH, CAE and test engineers in automotive, aerospace and machinery who post-process FRFs from shaker or impact-hammer tests, or from Nastran SOL111 / Abaqus steady-state dynamics runs.

    Built-in engineering checks

    It flags closely spaced (coupled) modes where half-power damping is biased, damping values that point to noise or leakage, and frequency resolution too coarse for reliable damping, then recommends next steps (curve-fitting, damping treatment, model updating).

    Input formats

    CSV, TXT or Excel with frequency plus real/imag, magnitude/phase, or dB/phase columns. Format is auto-detected.

    Limitations

    SISO FRFs only (no mode shapes). Half-power damping is an estimate; for heavily damped or closely spaced modes use a dedicated curve-fitter such as PolyMAX/LSCF.

    Supports SISO FRFs only. Half-power damping is unreliable for coupled modes or resolution coarser than 1 Hz below 200 Hz. No geometry/mode shape visualization.

    How to use

    1. 1

      Connect your agent to the Agensi MCP

      Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup

    2. 2

      Sign in to Agensi

      Your agent shows a sign-in link. Sign in and click Allow.

    3. 3

      Ask for what you need

      Your agent loads this skill and uses it on your task. It always asks before any payment.

    Reviews

    No reviews yet

    Be one of the first to try it. Every listed skill goes through the trust checks below.

    Security scanned

    Checked by our 8-point scan before listing

    Fresh listing

    Recently published to Agensi

    Free forever

    No account required to browse

    Trust & safety

    Security scan

    Security scan passed 20 days ago

    • Free with an Agensi account

    Requires

    Python

    Permissions

    Terminal / Shell
    Read Files
    Write Files

    Runs a local Python script that reads the FRF files you point it to and writes results (CSV, PNG, Markdown) to an output folder. No network access.

    Listed20 days ago

    What's inside

    Frequently Asked Questions

    The skill supports standard CSV, TXT, and Excel exports from major engineering software such as Nastran, Abaqus, Simcenter, LMS, and HEAD acoustics, provided they contain magnitude/phase or real/imaginary components.

    Unlike a standard LLM, this skill uses dedicated SciPy and NumPy libraries to perform precise mathematical interpolation and half-power bandwidth calculations that text-based models cannot reliably execute.

    The skill uses the half-power (-3 dB) bandwidth method to estimate damping ratios (zeta) and Q factors. It is accurate for lightly damped, well-separated modes; closely spaced modes are flagged so you can use a dedicated curve-fitter for them.

    The skill is free. You get the SKILL.md instructions, the Python analysis script (scripts/frf_analysis.py) and a requirements.txt. The script writes modes.csv, an FRF magnitude/phase plot and a Markdown report.

    Currently, the skill is optimized for Single-Input Single-Output (SISO) analysis; while it can process multiple files, it does not currently support MDOF curve fitting or the generation of animated mode shapes.

    The script warns when frequency resolution is coarser than 1 Hz below 200 Hz, where half-power damping becomes unreliable. The skill instructions also have the agent flag damping values above 10 % or below 0.1 % as likely noise or leakage artefacts. A prominence threshold (default 3 dB) suppresses noise peaks.

    New in Research & Analysis