Klipper Performance Tuning

    1

    Configure Klipper firmware, write G-code macros, and diagnose 3D print failures with safety-first tuning protocols.

    $15

    Secure checkout via Stripe

    Money-back guarantee

    Converts to your local currency at checkout

    Security scanned

    Works with the AI Agents you already use

    Claude CodeClaude CodeCursorCursorCodex CLICodex CLIMuseMuseDotsDots+21 more

    Klipper Performance Tuning

    Example session with this skill installed

    My prints are lifting at the corners and I keep getting layer shifts on the Y-axis. Here is my printer.cfg and a photo of the failure. How do I fix this?

    • Read your context and instructions
    • Compiled the klipper performance tuning

    I have analyzed your symptoms and configuration. The lifting (warping) is likely a bed adhesion or thermal issue, while the Y-axis layer shift points to mechanical resistance or excessive acceleration.

    Diagnosis and Recovery Plan

    SymptomDetected IssueRecommended Action
    Corner WarpingFirst layer Z-offset too high / Bed tempRecalibrate Z-offset; increase bed temp by 5C; check for drafts.
    Y-Axis ShiftBelt tension / AccelerationCheck Y-belt for slack; verify eccentric nuts; reduce max_accel in [printer].
    Thermal Configverify_heater standardKeep current safety settings; do not disable thermal protection.

    Proposed printer.cfg Adjustments

    [printer]
    kinematics: cartesian
    
    # Reduced from 3000 to 2000 to troubleshoot layer shifts
    max_velocity: 300
    max_accel: 2000
    max_z_velocity: 5
    max_z_accel: 100
    
    [stepper_y]
    
    # Verify physical belt tension before increasing current
    run_current: 0.800
    
    # Ensure this matches your board's official pinout
    # step_pin: ...
    # dir_pin: ...
    

    Next steps
    1.

    Mechanical Check: Physically pluck the Y-axis belt; it should have a low bass note, not be floppy or overly tight.
    2. Z-Offset: Run PROBE_CALIBRATE to ensure the first layer is getting sufficient squish to prevent warping.
    3.

    Validation: Save these changes, run FIRMWARE_RESTART, and attempt a small calibration cube to verify the shift is resolved.

    Connects securely to your tools. The creator never sees your data.

    About this skill

    Input shaping, pressure advance, flow and failure diagnosis.

    Configure, tune and troubleshoot 3D printers running Klipper (printer.cfg, macros, input shaping, pressure advance, bed mesh) or OctoPrint, and diagnose failed prints from photos and symptoms. Use when the user sets up or edits a Klipper config, writes print start/end macros, tunes print quality, or asks why a print failed (stringing, layer shift, warping, under-extrusion, clogging).

    Includes an EXPERT.md reference (exact parameters, thresholds, failure diagnosis).

    Acceptable use: civil and commercial printing only. The skill refuses firearm parts, lock-bypass devices and counterfeit safety-critical parts, and never disables thermal runaway protection, heater verification or endstops.

    Cannot override safety features like thermal runaway protection or max temperature limits. User must manually perform firmware restarts and physical measurements.

    How to use

    1. 1

      Connect your agent to the Agensi MCP

      Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup

    2. 2

      Sign in to Agensi

      Your agent shows a sign-in link. Sign in and click Allow.

    3. 3

      Ask for what you need

      Your agent loads this skill and uses it on your task. It always asks before any payment.

    Reviews

    No reviews yet

    Be one of the first to try it. Every listed skill goes through the trust checks below.

    Security scanned

    Checked by our 8-point scan before listing

    Fresh listing

    Recently published to Agensi

    Money-back guarantee

    Doesn't do what its page promises? You get your money back.

    Trust & safety

    Security scan

    Security scan passed 28 days ago

    Permissions

    Network Access
    Read Files
    Listed28 days ago

    What's inside

    Frequently Asked Questions

    This skill provides specialized assistance for editing `printer.cfg` files, creating complex G-code macros, and following step-by-step calibration protocols like PID tuning and pressure advance. It ensures your configuration follows the correct tuning sequence to prevent hardware damage or failed prints.

    While this skill provides the configuration blocks and logic for Klipper, Moonraker, and interfaces like Mainsail or Fluidd, users must still manually perform a `FIRMWARE_RESTART` and verify physical hardware connections for safety.

    This skill is compatible with any AI agent that supports code-block generation and markdown, and it is optimized for users running Klipper on Raspberry Pi or similar SBCs regardless of the specific printer brand.

    For safety reasons, this skill will not assist in disabling thermal runaway protection (`verify_heater`) or exceeding the manufacturer's `max_temp` limits to protect your hardware and home.

    You receive a comprehensive suite of logic modules for configuration management, failure diagnosis workflows, and macro development templates specifically tuned for the Klipper ecosystem.

    New in Workflow Automation